ADAM-4100 Series User Manual Ed 1.2

研华模块的资料

ADAM 4100

Industrial Grade Data Acquisition Modules

User's Manual

研华模块的资料

Copyright Notice

This document is copyrighted, 2005, by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd., reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements upon the rights of third parties, which may result from its use.

CE Notification

The ADAM-4100 series developed by Advantech Co., Ltd. has passed the CE test for environmental specifications. Therefore, in order to protect the ADAM modules from being damaged by ESD (Electric Static Discharge), we strongly recommend that the use of CE-compliant industrial enclosure products when using any ADAM module.

FCC Class A

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Edition 1.2 Aug. 2007

研华模块的资料

Table of Contents

Chapter 1 Introduction ..….....……..................…..................………….. 1-1

Chapter 2 Installation Guideline ...................….................…...................2-1 2.1 System Requirements to set up an ADAM network ..…...............2-2 2.2 Basic configuration and hook-up .................……...........................2-5 2.3 Baud rate and Checksum .................................……........................2-7 2.4 Multiple Module Hookup ...............................………......................2-9 2.5 Programming Example.....................................…….......................2-10

Chapter 3 I/O Modules ..................................................…........................ 3-1 3.1 The common specification of ADAM-4100 I/O series....…............3-2 3.2 ADAM-4117 8-channel Analog Input Module…….…................3-3 3.3 ADAM-4118 8-channel Thermocouple Input Module….…........3-6 3.4 ADAM-4150 Digital I/O Module............……................…..........3-10 3.5 ADAM-4168 Relay Output Module.......... ……………………..3-14

Chapter 4 Command Set ..................................................…......................4-1 4.1 Introduction.............................................................….......................4-2 4.2 Syntax .....................................................................…........................4-2 4.3 Analog I/O Module Commands Search Table.............…...............4-4 4.4 Analog I/O Module Command set...............................…................4-6 4.5 Digital I/O Module Commands Search Table.............…...............4-31 4.6 Digital I/O Module Command set……………..........….................4-34

Chapter 5 Calibration ...........................................…..................................5-1 5.1 Analog Input Module Calibration ............................… ....................5-2

研华模块的资料

Appendix A Utility Software..............................…......... …………...…..A-1 A.1 Utility overview............…...............................................................A-2 A.2 Firmware update............................................................……........A-6 A.3 Address mode..................................................................................A-8 A.4 Locate mode................................…................................................A-9

Appendix B ADAM-4100 I/O Modbus Mapping Table....…..................B-1 B.1 ADAM-4117 8-channel Analog Input Module............…............. B-3 B.2 ADAM-4118 8-channel Thermocouple Input Module.................B-4 B.3 ADAM-4150 Digital Input/Output Module.......................…........B-5 B.4 ADAM-4168 8 Relay Output Module………………..…..............B-9

Appendix C Technical Diagrams .................................…........................C-1 C.1 ADAM Dimensions ............................................…..........................C-2 C.2 Installation ...........................................................….........................C-3

Appendix D Data Formats and I/O Ranges...................…......................D-1 D.1 Analog Input Formats......................…............................................D-2

Appendix E RS-485 Network .............................…..................................E-1 E.1 Basic Network Layout ................................….................................E-3 E.2 Line Termination .........................................…................................E-5 E.3 RS-485 Data Flow Control ..............................................................E-7

Appendix F How to use the Checksum feature...........….........................F-1 F.1 Checksum Enable/Disable ......................................…............. …… 此处隐藏：15711字，全部文档内容请下载后查看。喜欢就下载吧 ……